Objective - SS0721A0004
Figure 1. Typical AN/VIC-1(V) without FM radio.
Figure 2. AM-1780/VRC jacks, control, and indicator.
Figure 3. C-2298 jacks and controls.
Figure 4. Cable assembles.
Figure 5. Cable assembly CX-4723/VRC.
Figure 6. Typical audio accessories used with AN/VIC-1(V) control boxes.
Figure 7. CVC helmet (T56-6) and AVC helmet (DH-132).
Figure 8. AM-1780 jacks and binding post locations.
Figure 9. AM-1780 control and switch locations.
Figure 10. C-2298/VRC jacks and control locations.
Figure 11. Typical connections of audio accessories to control boxes.
Figure 12. Audio accessory connector.
Figure 13. AM-1780 and C-2298 controls set for intercom operation.
Figure 14. Typical AN/VIC-1(V) cabling for intercom operation.
Figure 15. DA Form 2404.
Figure 16. Initial adjustments, Section I of GTA 11-3-49.
Figure 17. Typical AN/VIC-1 cabling without FM radio.
Figure 18. AM-1780.
Figure 19. C-2298 VOLUME control and MONITOR switch.
Figure 20. H-189/U(H-250/U) handset checks.
Figure 21. EPC step la and vehicle MASTER SWITCH set at ON.
Figure 22. EPC step 1b and MX-7777 circuit breaker set to ON.
Figure 23. AM-1780 MAIN PWR switch at INT ONLY, POWER lamp not lit.
Figure 24. AM-1780 POWER CKT BKR set at ON and AM-1780 POWER lamp lights.
Figure 25. Handset connected to commander's C-2298 intercom jack J803.
Figure 26. Handset connected to C-2298 RAD jack J802.
EPC step 3.
EPC step 4.
EPC step 5.
Figure 27. Completed DA Form 2404 for a no-fault op check.
Figure 28. DA Form 2404 completed when fault found that requires support maintenance repairs.
Evaluate the Operation of Intercommunications Set AN/VIC-1(V)
Figure 1. Typical AN/VIC-1(V) without FM radio.
Figure 2. AM-1780/VRC jacks, control, and indicator.
Figure 3. C-2298 jacks and controls.
Figure 4. Cable assembles.
Figure 5. Cable assembly CX-4723/VRC.
Figure 6. Typical audio accessories used with AN/VIC-1(V) control boxes.
Figure 7. CVC helmet (T56-6) and AVC helmet (DH-132).
Figure 8. AM-1780 jacks and binding post locations.
Figure 9. AM-1780 control and switch locations.
Figure 10. C-2298/VRC jacks and control locations.
Figure 11. Typical connections of audio accessories to control boxes.
Figure 12. Audio accessory connector.
Figure 13. AM-1780 and C-2298 controls set for intercom operation.
Figure 14. Typical AN/VIC-1(V) cabling for intercom operation.
Figure 15. DA Form 2404.
Figure 16. Initial adjustments, Section I of GTA 11-3-49.
Figure 17. Typical AN/VIC-1 cabling without FM radio.
Figure 18. AM-1780.
Figure 19. C-2298 VOLUME control and MONITOR switch.
Figure 20. H-189/U(H-250/U) handset checks.
Figure 21. EPC step la and vehicle MASTER SWITCH set at ON.
Figure 22. EPC step 1b and MX-7777 circuit breaker set to ON.
Figure 23. AM-1780 MAIN PWR switch at INT ONLY, POWER lamp not lit.
Figure 24. AM-1780 POWER CKT BKR set at ON and AM-1780 POWER lamp lights.
Figure 25. Handset connected to commander's C-2298 intercom jack J803.
Figure 26. Handset connected to C-2298 RAD jack J802.
EPC step 3.
EPC step 4.
EPC step 5.
Figure 27. Completed DA Form 2404 for a no-fault op check.
Figure 28. DA Form 2404 completed when fault found that requires support maintenance repairs.
Evaluate the Operation of Intercommunications Set AN/VIC-1(V)
